Saturday Night Racer

hookdup LMR Rookie Offline I love YaBB 1G - SP1! Posts: 46	Rod Length 04/10/10 at 4:09am In a 23 degree steel head limited late model engine with a 50 lb. 3.500 max stroke crank and flat top pistons, would you use a 6 inch (or longer) rod or stick with stock length (5.7) rod? And why? I am having a debate with a friend of mine and need ammo..... Thanks!
Back to top	IP Logged

TIM_BEWLEY LMR God Offline road zombie Posts: 1629	Re: Rod Length Reply #1 - 04/10/10 at 8:25am well you will probally get some different opions but i have always liked the 6" rod. less rod angle on the cyl. walls, stays around tdc & bdc longer. i'm not a pro engine builder it just what i like. check out this like http://www.chevymania.com/tech/rod.htm
Back to top	PAN OFF GETTING A 1" INSPECTION PLUG! IP Logged

Andrew

LMR God

Offline

2006 SMS M.S.
champion... more of
a PB these days

Posts: 1359
Camarillo

Re: Rod Length
Reply #2 - 04/10/10 at 8:52am

I agree with Tim, I like 6" rods(that just doesn't sound right though). I'm no pro builder either. I can't get technical, but the benefit of the 6" rod is based on the relationship between the bore and stroke. There are engines, that are built right from the factory, and they have a long enough rod(mostly imports). If I were building a small block, I'd want the 6"ers.

Back to top

IP Logged

OLD SCHOOL#6

LMR God

Offline

CHEVY RUMBLE !!

Posts: 2452

Re: Rod Length
Reply #3 - 04/10/10 at 9:06am

Oh-Geeez, I guess I will have to agree with Tim also. My knowledge is that long rods will not gain much more HP than 1 - 3% but there are some gains there to be had. The big gains are in the stress areas on your motor. Short rod exerts more force to the crank pin at any crank angle that counts (ie.20-deg ATDC to 70-deg ATDC). Also short rods will side load cylinder walls more than long rods (this one is the big one to me). Using short rods will make piston design selection and cylinder wall rigidity more important. There is a lot more to the subject than this, but it's about all I know ................... Tim's link is pretty good................

Back to top

"SMOKE ' UM" -- the unlawfull act of depositing large amounts of rubber on a hard surface such as asphalt or concrete.

AIM

IP Logged

Andrew LMR God Offline 2006 SMS M.S. champion... more of a PB these days Posts: 1359 Camarillo	Re: Rod Length Reply #4 - 04/10/10 at 12:08pm Cyl wall load = heat. The one long rod motor I build(4 cyl) had a real hard time getting hot. I had to use a 195* thermostat and drain some water from the radiator to keep the engine from running too cool on those cold spring nights. Kind of a good problem to have though.
Back to top	IP Logged

hogracer3d LMR God Offline We bust our a$$ to kick yours-!!! Posts: 3933	Re: Rod Length Reply #5 - 04/10/10 at 1:25pm Smokey Yunick and Randy Dorton say, put the longest rod in that will fit. lighter piston, likes more rpm, but becomes very cam dependant. A good long rod camshaft, will make the difference between a rocket and a turd A limited late is the perfect application for a 6.200+ rod package, especially if on a 2-bbl
Back to top	DSClaimer: I have no DNA evidence that my post is absolutely 100% true and accurate, and frankly don't care ! IP Logged

hookdup LMR Rookie Offline I love YaBB 1G - SP1! Posts: 46	Re: Rod Length Reply #6 - 04/24/10 at 4:31am Thanks y'all!!!
Back to top	IP Logged